View R1163N301D-TR-FE_8723616.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

r1163x series 3-mode 150ma ldo regulator with the reverse current protection no.ea-118-140724 1 outline the r1163x series consist of cmos-based voltage regul ator ics with high output voltage accuracy and low supply current. these ics perform with the chip enable function and realize a standby mode with ultra low supply current. to prevent the destruction by over current, the current limit circui t is included. the r1163x series have 3-mode. one is standby mode with ce or standby control pin. other two modes are realized with eco pin. fast transient mode (ft mode) and low power mode (lp mode) ar e alternative with eco pi n. consumption current is reduced at low power mode compared with fast tr ansient mode. the output voltage is maintained between ft mode and lp mode. further, the reverse current protection circuit is built-in. therefore, if a higher voltage than v dd pin is forced to the output pin, the reverse current to v dd pin is very small (max. 0.1 a) , so it is suitable for backup circuit. since the packages for these ics are sot-23-5, son-6, and dfn(plp)1616-6 packages, high density mounting of the ics on boards is possible. features ? supply current ..................................................... typ. 6.0 a (low power mode), typ. 70 a (fast transient mode) ? standby mode ...................................................... typ. 0.6 a ? reverse current ................................................... max. 0.1 a ? input voltage range ............................................ 2.0v to 6.0v ? output voltage range .......................................... 1.5v to 5.0v (0.1v steps) ( for other voltages, please refer to mark informations.) ? output voltage accuracy ...................................... 1.5% ( 2.5% at low power mode) ? temperature-drift coefficient of output voltage .. typ. 100ppm/ c ? dropout voltage ................................................... typ. 0.25v (i out = 150ma, v out = 2.8v) ? ripple rejectio n ................................................... typ. 70db (f = 1khz, fast transient mode) ? line regulation .................................................... typ. 0.02%/v (fast transient mode) ? packages ............................................................ dfn(plp)1616-6, sot-23-5, son-6 ? built-in fold-back protection circuit ....................... typ. 40ma (current at short mode) ? performs with ceramic capacitors ...................... c in = ceramic 1.0 f, c out = ceramic 0.47 f applications ? precision voltage references. ? power source for electrical appliances such as cameras, vcrs and hand-held communication equipment. ? power source for battery-powered equipment.
r1163x 2 block diagram r1163xxx1b r1163xxx1d v dd gnd v out eco ce vref current limit reverse detector v dd gnd v out eco ce vref current limit reverse detecto r r1163xxx1e v dd gnd v out eco ce vref current limit reverse detector
r1163x 3 selection guide the output voltage, auto discharge function, and packag e, etc. for the ics can be selected at the user?s request. product name package quantity per reel pb free halogen free r1163kxx1 ? -tr dfn(plp)1616-6 5,000 pcs yes yes r1163nxx1 ? -tr-fe sot-23-5 3,000 pcs yes yes r1163dxx1 ? -tr-fe son-6 3,000 pcs yes yes xx : the output voltage can be designated in the rang e from 1.5v(15) to 5.0v(50) in 0.1v steps. (for other voltages, please refer to mark informations.) ? : the auto discharge function at off state are options as follows. (b) without auto discharge function at off state (d) with auto discharge function at off state (e) without auto discharge function at off stat e, eco logic reverse type (low power mode at eco = "h")
r1163x 4 pin configurations ? dfn(plp)1616-6 ? sot-23-5 ? son-6 1 2 3 6 5 4 32 1 4 5 6 ? top view bottom view 12 3 4 5 (mark side) top view bottom view 6 5 4 4 5 6 1 2 3 3 2 1 ?? pin discriptions ? dfn(plp)1616-6 pin no symbol pin description 1 v out output pin 2 gnd ground pin 3 eco/ eco mode alternative pin 4 ce chip enable pin ("h" active) 5 nc no connection 6 v dd input pin ? ) tab is gnd level. (they are connected to the reverse side of this ic.) the tab is better to be connected to the gn d, but leaving it open is also acceptable. ? sot-23-5 pin no symbol pin description 1 v dd input pin 2 gnd ground pin 3 ce chip enable pin ("h" active) 4 eco/ eco mode alternative pin 5 v out output pin ? son-6 pin no symbol pin description 1 v dd input pin 2 nc no connection 3 v out output pin 4 eco/ eco mode alternative pin 5 gnd ground pin 6 ce chip enable pin ("h" active) *) tab suspension leads are gnd level. (they are connected to the reverse side of this ic.) the tab suspension leads should be open and do not connect to other wires or land patterns.
r1163x 5 absolute maximum ratings symbol item rating unit v in input voltage 6.5 v v eco input voltage (eco/ eco pin) ? 0.3 ~ 6.5 v v ce input voltage (ce pin) ? 0.3 ~ 6.5 v v out output voltage ? 0.3 ~ 6.5 v i out output current 180 ma p d power dissipation (dfn(plp)1616-6)* 640 mw power dissipation (sot-23-5) * 420 power dissipation (son-6) * 500 topt operating temperature range ? 40 ~ 85 c tstg storage temperature range ? 55 ~ 125 c ? ) for power dissipation, please refer to package information. absolute maximum ratings electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent damages and may degrade the life time and safety for both device and sy stem using the device in the field. the functional operation at or over these absolute maximum ratings is not assured. recommended operating conditions (electrical characteristics) all of electronic equipment should be designed that the mounted semiconductor devices operate within the recommended operating conditions. the semiconductor devices cannot operate normally over the recommended operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. and the semiconductor de vices may receive serious damage when they continue to operate over the recommended operating conditions.
r1163x 6 electrical characteristics r1163xxx1b/d topt = 25 c symbol item conditions min. typ. max. unit v out output voltage ft mode v in = + = < = < = 0.985 1.015 v lp mode v in = + = < = < = 0.975 1.025 v out output voltage deviation between ft mode and lp mode v in = set v out + 1v, i out = 30ma v out > 2.0v ? 1.2 0 1.2 % v out < = ? 24 0 24 mv i out output current v in ? = v out / i out load regulation ft mode v in = + = < = < = = + = < = < = = + = v in 70 100 a i ss2 supply current (lp mode) v in = + = gnd 6.0 10.0 a i standby supply current (standby) v in = + = = gnd or v in 0.6 1.0 a v out / v in line regulation ft mode set v out + 0.5v < = < = = 30ma, v eco = v in if v out < = < = < = + 0.5v < = < = = 30ma, v eco = gnd if v out < = < = < = = set v out + 1v, i out = 30ma, v eco = v in if v out < = = set v out + 1.2v f = 1khz 70 db f = 10khz 60 v in input voltage 2.0 6.0 v v out / t opt output voltage temperature coefficient i out = ? 40 c < = < = c 100 ppm / c i sc short current limit v out = = vrms output noise "l" (lp mode) bw = = 0v 60 i rev reverse current v out >0.5v, 0v < = < =
r1163x 7 r1163xxx1e topt = 25 c symbol item conditions min. typ. max. unit v out output voltage ft mode v in = + = < = < = 0.985 1.015 v lp mode v in = + = < = < = 0.975 1.025 v out output voltage deviation between ft mode and lp mode v in = set v out + 1v, i out = 30ma v out > 2.0v ? 1.2 0 1.2 % v out < = ? 24 0 24 mv i out output current v in ? = v out / i out load regulation ft mode v in = + = < = < = = + = < = < = = + = gnd 70 100 a i ss2 supply current (lp mode) v in = + = v in 6.0 10.0 a i standby supply current (standby) v in = + = = gnd or v in 0.6 1.0 a v out / v in line regulation ft mode set v out + < = < = = 30ma, v eco = gnd if v out < = < = < = + < = < = = 30ma, v eco = v in if v out < = < = < = = set v out + 1v, i out = 30ma, v eco = gnd if v out < = = set v out + 1.2v f = 1khz 70 db f = 10khz 60 v in input voltage 2.0 6.0 v v out / t opt output voltage temperature coefficient i out = ? 40 c < = < = c 100 ppm / c i sc short current limit v out = = vrms output noise "l" (lp mode) bw = < = < =
r1163x 8 electrical characteristics by output voltage topt = 25 c output voltage v out (v) dropout voltage (mv) condition v dif (eco=h) v dif (eco=l) typ. max. typ. max. 1.5 < = v out < 1.6 i out = 150ma 400 680 420 680 1.6 < = v out < 1.7 380 550 390 550 1.7 < = v out < 1.8 350 520 370 520 1.8 < = v out < 2.0 340 490 350 490 2.0 < = v out < 2.8 290 425 300 430 2.8 < = v out < = 5.0 250 350 250 350 typical application c1 r1163x series v dd v out ce gnd v out eco c2 ( external components) ex. c1: ceramic capacitor 1.0 f c2: ceramic capacitor 0.47 f murata grm40b474k kyocera cm105b474k technical notes when using these ics, consider the following points: phase compensation in these ics, phase compensation is made for securing st able operation even if the load current is varied. for this purpose, be sure to use a 0.47 f or more ceramic capacitor c2. (test these ics with as same external components as ones to be used on the pcb.) when a tantalum capacitor is used with this ic, if the equi valent series resistor (esr) of the capacitor is large, output voltage may be unstable. pcb layout make v dd and gnd lines sufficient. if their impedance is hi gh, noise pickup or unstable operation may result. connect a capacitor c1 with as much as 1.0 f capacitor between v dd and gnd pin as close as possible. set external components such as an output capacitor c2, as close as possible to the ics and make wiring as short as possible.
r1163x 9 test circuits r1163x series v dd ce v out gnd c2 eco v v out c1 i out c1=ceramic 1.0 f c2=ceramic 0.47 f basic test circuit i ss a r1163x series v dd ce v out gnd c2 eco v out c1 c1=ceramic 1.0 f c2=ceramic 0.47 f test circuit for supply current pulse generator v dd ce v out gnd c2 i out r1163x series eco c1=ceramic 1.0 f c2=ceramic 0.47 f p. g. test circuit for ripple rejection, line transient response
r1163x 10 v dd ce v out gnd c2 c1 v out v i out b i out a r1163x series eco c1=ceramic 1.0 f c2=ceramic 0.47 f test circuit for load transient response pulse generator v dd ce v out gnd c2 i out r1163x series eco c1=ceramic 1.0 f c2=ceramic 0.47 f p. g. c1 test circuit for output voltage at mode alternative point pulse generator p. g. c1 c1=ceramic 1.0 f v dd ce v out gnd c2 i out r1163x series eco ? ce pin input waveform 0v set v out +1.0v test circuit for turn on speed with ce pin
r1163x 11 typical characteristics unless otherwise provided, capacitors are ceramic type. 1) output voltage vs. output current r1163x151x eco=h r1163x151x eco=l 0 300 200 100 400 output current i out (ma) output voltage h v out h(v) 0.0 0.2 0.4 0.6 0.8 1.2 1.0 1.4 1.6 v in =2v v in =2.5v ? 3.5v 0 300 200 100 400 output current i out (ma) output voltage l v out l(v) 0.0 0.2 0.4 0.6 0.8 1.2 1.0 1.4 1.6 v in =2v v in =2.5v ? 3.5v r1163x281x eco=h r1163x281x eco=l 0 300 200 100 400 output current i out (ma) output voltage h v out h(v) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v in =3.1v v in =3.3v v in =3.8v ? 4.8v 0 300 200 100 400 output current i out (ma) output voltage l v out l(v) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 v in =3.1v v in =3.3v v in =3.8v ? 4.8v r1163x40x eco=h r1163x40x eco=l 0 300 200 100 400 output current i out (ma) output voltage h v out h(v) 0.0 0.5 1.0 2.0 3.0 4.0 1.5 2.5 3.5 4.5 v in =4.3v v in =4.5v v in =5v ? 6v 0 300 200 100 400 output current i out (ma) output voltage l v out l(v) 0.0 0.5 1.0 2.0 3.0 4.0 1.5 2.5 3.5 4.5 v in =4.3v v in =4.5v v in =5v ? 6v
r1163x 12 2) output voltage vs. input voltage r1163x151x eco=h r1163x15x eco=l 02 5 14 36 input voltage v in (v) output voltage h v out h(v) 0.0 0.2 0.4 0.6 0.8 1.2 1.0 1.4 1.6 i out =1ma i out =30ma i out =50ma 02 5 14 36 input voltage v in (v) output voltage l v out l(v) 0.0 0.2 0.4 0.6 0.8 1.2 1.0 1.4 1.6 i out =1ma i out =30ma i out =50ma r1163x28x eco=h r1163x28x eco=l 02 5 14 36 input voltage v in (v) output voltage h v out h(v) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 i out =1ma i out =30ma i out =50ma 02 5 14 36 input voltage v in (v) output voltage l v out l(v) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 i out =1ma i out =30ma i out =50ma r1163x40x eco=h r1163x40x eco=l 02 5 14 36 input voltage v in (v) output voltage h v out h(v) 0.0 0.5 1.0 1.5 2.5 3.5 2.0 3.0 4.0 4.5 i out =1ma i out =30ma i out =50ma 02 5 14 36 input voltage v in (v) output voltage l v out l(v) 0.0 0.5 1.0 1.5 2.5 3.5 2.0 3.0 4.0 4.5 i out =1ma i out =30ma i out =50ma
r1163x 13 3) supply current vs. input voltage r1163x151x eco=h r1163x151x eco=l 024 1356 input voltage v in (v) 0 20 40 10 30 50 60 70 80 supply current h i ss h ( a) 024 1356 input voltage v in (v) 0 2 4 1 3 5 6 7 8 supply current i ss ( a) r1163x281x eco=h r1163x281x eco=l 024 1356 input voltage v in (v) 0 20 40 10 30 50 60 70 80 supply current h i ss h ( a) 024 1356 input voltage v in (v) 0 2 4 1 3 5 6 7 8 supply current i ss ( a) r1163x401x eco=h r1163x401x eco=l 024 1356 input voltage v in (v) 0 20 40 10 30 50 60 70 80 supply current h i ss h (a) 024 1356 input voltage v in (v) 0 2 4 1 3 5 6 7 8 supply current i ss (a)
r1163x 14 4) output voltage vs. temperature r1163x151x eco=h r1163x151x eco=l 1.46 1.48 1.47 1.53 1.52 1.50 1.49 1.51 -50 0-25 50 75 25 100 temperature topt(c) output voltage h v out h (v) 1.46 1.48 1.47 1.53 1.52 1.50 1.49 1.51 -50 0-25 50 75 25 100 temperature topt(c) output voltage l v out l (v) r1163x281x eco=h r1163x281x eco=l 2.76 2.77 2.83 2.81 2.79 2.78 2.82 2.80 -50 0-25 50 75 25 100 temperature topt(c) output voltage h v out h (v) 2.76 2.77 2.83 2.81 2.79 2.78 2.82 2.80 -50 0-25 50 75 25 100 temperature topt(c) output voltage l v out l (v) r1163x401x eco=h r1163x401x eco=l 3.97 3.99 3.98 4.05 4.03 4.01 4.00 4.04 4.02 -50 0-25 50 75 25 100 temperature topt(c) output voltage h v out h (v) 3.98 3.99 4.06 4.05 4.03 4.01 4.00 4.04 4.02 -50 0-25 50 75 25 100 temperature topt(c) output voltage l v out l (v)
r1163x 15 5) supply current vs. temperature r1163x151x eco=h r1163x151x eco=l -50 0 50 -25 25 75 100 temperature topt(c) 0 20 40 10 30 50 60 70 90 80 supply current h i ss h ( a) v in =2.5v -50 0 50 -25 25 75 100 temperature topt(c) 0 2 4 1 3 5 6 7 10 9 8 supply current i ss ( a) v in =2.5v r1163x281x eco=h r1163x281x eco=l -50 0 50 -25 25 75 100 temperature topt(c) 0 20 40 10 30 50 60 70 90 80 supply current h i ss h ( a) v in =3.8v -50 0 50 -25 25 75 100 temperature topt(c) 0 2 4 1 3 5 6 7 10 9 8 supply current i ss ( a) v in =3.8v r1163x401x eco=h r1163x401x eco=l -50 0 50 -25 25 75 100 temperature topt(c) 0 20 40 10 30 50 60 70 90 80 supply current h i ss h (a) v in =5.0v -50 0 50 -25 25 75 100 temperature topt(c) 0 2 4 1 3 5 6 7 10 9 8 supply current i ss (a) v in =5.0v
r1163x 16 6) standby current vs. input voltage 02 5 14 36 input voltage v in (v) standby current istb(a) 0.0 0.5 1.0 1.5 2.0 2.5 topt=85c topt=25c topt=-40c 7) reverse current vs. output voltage v in =1v 1.5 3.0 5.5 2.0 5.0 4.03.5 2.5 4.5 6.0 output voltage v out (v) 0.000 0.004 0.008 0.012 0.016 0.018 0.002 0.006 0.010 0.014 0.020 topt=85c topt=25c topt=-40c i rev1 (a) 0.0 0.8 1.8 0.2 0.4 1.6 1.21.0 0.6 1.4 2.0 output voltage v out (v) 0.0 0.4 0.8 0.2 0.6 1.0 1.2 topt=85c topt=25c topt=-40c v in =0v i rev3 (a) 8) dropout voltage vs. output current r1163x151x eco=h r1163x151x eco=l 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage h v dif _h(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage l v dif _l(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc
r1163x 17 r1163x161x eco=h r1163x161x eco=l 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage h v dif _h(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage l v dif _l(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc r1163x171x eco=h r1163x171x eco=l 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage h v dif _h(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage l v dif _l(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc r1163x181x eco=h r1163x181x eco=l 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage h v dif _h(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc 0 0.1 0.2 0.3 0.4 0.5 0 25 50 75 100 125 150 dropout voltage l v dif _l(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc
r1163x 18 r1163x211x eco=h r1163x211x eco=l 0 0.1 0.2 0.3 0.4 0 25 50 75 100 125 150 dropout voltage h v dif _h(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc 0 0.1 0.2 0.3 0.4 0 25 50 75 100 125 150 dropout voltage l v dif _l(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc r1163x281x eco=h r1163x281x eco=l 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0 255075100125150 dropout voltage h v dif _h(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0 25 50 75 100 125 150 dropout voltage l v dif _l(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc r1163x401x eco=h r1163x401x eco=l 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0 255075100125150 dropout voltage h v dif _h(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0 25 50 75 100 125 150 dropout voltage l v dif _l(v) output current i out (ma) topt=85oc topt=25oc topt=-40oc
r1163x 19 9) dropout voltage vs. set output voltage r1163x eco=h r1163x eco=l 0.00 0.10 0.20 0.30 0.40 0.50 1.5 2.0 2.5 3.0 3.5 4.0 dropout voltage h v dif _h(v) set output voltage v reg (v) iout=10ma iout=30ma iout=50ma iout=100ma iout=150ma 0.00 0.10 0.20 0.30 0.40 0.50 1.5 2.0 2.5 3.0 3.5 4.0 dropout voltage l v dif _l(v) set output voltage v reg (v) iout=10ma iout=30ma iout=50ma iout=100ma iout=150ma 10) ripple rejection vs. input bias voltage r1163x281x eco=h r1163x281x eco=h 2.9 3.1 3.0 3.2 3.3 input voltage v in (v) 0 20 40 10 30 50 60 70 90 80 ripple rejection rr(db) f=1khz f=10khz f=100khz c in =none, c out =0.47f, i out =1ma ripple=0.2vp-p 2.9 3.1 3.0 3.2 3.3 input voltage v in (v) 0 20 40 10 30 50 60 70 90 80 ripple rejection rr(db) c in =none, c out =0.47f, i out =1ma ripple=0.5vp-p f=1khz f=10khz f=100khz r1162x281x eco=h r1162x281x eco=h 2.9 3.1 3.0 3.2 3.3 input voltage v in (v) 0 20 40 10 30 50 60 70 90 80 ripple rejection rr(db) c in =none, c out =0.47f, i out =30ma ripple=0.2vp-p f=1khz f=10khz f=100khz 2.9 3.1 3.0 3.2 3.3 input voltage v in (v) 0 20 40 10 30 50 60 70 90 80 ripple rejection rr(db) c in =none, c out =0.47f, i out =30ma ripple=0.5vp-p f=1khz f=10khz f=100khz
r1163x 20 r1163x281x eco=h r1163x281x eco=h 2.9 3.1 3.0 3.2 3.3 input voltage v in (v) 0 20 40 10 30 50 60 70 90 80 ripple rejection rr(db) c in =none, c out =0.47f, i out =50ma ripple=0.2vp-p f=1khz f=10khz f=100khz 2.9 3.1 3.0 3.2 3.3 input voltage v in (v) 0 20 40 10 30 50 60 70 90 80 ripple rejection rr(db) c in =none, c out =0.47f, i out =50ma ripple=0.5vp-p f=1khz f=10khz f=100khz 11) ripple rejection vs. frequency r1163x151x eco=h r1163x151x eco=l 0.1 1 10 100 frequency f(khz) 0 20 40 10 30 50 60 70 80 ripple rejection rr_h(db) c in =none, c out =0.47f, v in =2.5v dc +0.2vp-p i out =1ma i out =30ma i out =50ma 0.1 1 10 100 frequency f(khz) 0 20 40 10 30 50 60 70 ripple rejection rr_l(db) c in =none, c out =0.47f, v in =2.5v dc +0.2vp-p i out =1ma i out =30ma i out =50ma r1163x281x eco=h r1163x281x eco=l 0.1 1 10 100 frequency f(khz) 0 20 40 10 30 50 60 70 80 ripple rejection rr_h(db) c in =none, c out =0.47f, v in =3.8v dc +0.2vp-p i out =1ma i out =30ma i out =50ma 0.1 1 10 100 frequency f(khz) 0 20 40 10 30 50 60 70 ripple rejection rr_l(db) c in =none, c out =0.47f, v in =3.8v dc +0.2vp-p i out =1ma i out =30ma i out =50ma
r1163x 21 r1163x401x eco=h r1163x401x eco=l 0.1 1 10 100 frequency f(khz) 0 20 40 10 30 50 60 70 80 ripple rejection rr_h(db) c in =none, c out =0.47f, v in =5.0v dc +0.2vp-p i out =1ma i out =30ma i out =50ma 0.1 1 10 100 frequency f(khz) 0 20 40 10 30 50 60 70 ripple rejection rr_l(db) c in =none, c out =0.47f, v in =5.0v dc +0.2vp-p i out =1ma i out =30ma i out =50ma 12) input transient response r1163x151x eco=h r1163x151x eco=l 1.46 1.48 1.58 1.54 1.52 1.56 1.50 -2 0 -1 4 3 2 1 020 10 60 80 4030 70 90 50 100 time t(s) input voltage v in (v) c in =none, c out =0.47f i out =30ma output voltage v out (v) input voltage output voltage 0.5 1.0 3.5 2.5 2.0 3.0 1.5 -2 0 -1 4 3 2 1 0.0 0.20.1 0.6 0.8 0.40.3 0.7 0.9 0.5 1.0 time t(ms) input voltage v in (v) c in =none, c out =0.47f i out =10ma output voltage v out (v) input voltage output voltage r1163x151x eco=l r1163x281x eco=h 0.5 1.0 3.5 2.5 2.0 3.0 1.5 -2 0 -1 4 3 2 1 0.0 0.20.1 0.6 0.8 0.40.3 0.7 0.9 0.5 1.0 time t(ms) input voltage v in (v) c in =none, c out =1f i out =10ma output voltage v out (v) input voltage output voltage 2.76 2.78 2.88 2.84 2.82 2.86 2.80 0 2 1 6 5 4 3 020 10 60 80 4030 70 90 50 100 time t(s) input voltage v in (v) c in =none, c out =1f i out =30ma output voltage v out (v) input voltage output voltage
r1163x 22 r1163x281x eco=h 2.0 2.5 5.0 4.0 3.5 4.5 3.0 0 2 1 6 5 4 3 0.0 0.20.1 0.6 0.8 0.40.3 0.7 0.9 0.5 1.0 time t(ms) input voltage v in (v) c in =none, c out =1f i out =10ma output voltage v out (v) input voltage output voltage 13) load transient response r1163x151x eco=h r1163x151x eco=h 1.3 1.4 1.9 1.7 1.6 1.8 1.5 -150 -50 -100 150 100 50 0 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =2.5v, c in =1f c out =0.47f output voltage v out (v) output current output voltage 1.3 1.4 1.9 1.7 1.6 1.8 1.5 -150 -50 -100 150 100 50 0 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =2.5v, c in =1f c out =1.0f output voltage v out (v) output current output voltage r1163x151x eco=h r1163x151x eco=h 1.3 1.4 1.9 1.7 1.6 1.8 1.5 -120 -60 -90 60 30 0 -30 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =2.5v, c in =1f c out =0.47f output voltage v out (v) output current output voltage 1.3 1.4 1.9 1.7 1.6 1.8 1.5 -120 -60 -90 60 30 0 -30 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =2.5v, c in =1f c out =1.0f output voltage v out (v) output current output voltage
r1163x 23 r1163x151x eco=l r1163x151x eco=l 1.3 1.4 1.9 1.7 1.6 1.8 1.5 -40 -20 -30 20 10 0 -10 0.0 0.40.2 1.2 1.6 0.80.6 1.4 1.8 1.0 2.0 time t(ms) output current i out (ma) v in =2.5v, c in =1f c out =0.47f output voltage v out (v) output current output voltage 1.3 1.4 1.9 1.7 1.6 1.8 1.5 -40 -20 -30 20 10 0 -10 0.0 0.40.2 1.2 1.6 0.80.6 1.4 1.8 1.0 2.0 time t(ms) output current i out (ma) v in =3.8v, c in =1f c out =1f output voltage v out (v) output current output voltage r1163x281x eco=h r1163x281x eco=h 2.6 2.7 3.2 3.0 2.9 3.1 2.8 -150 -50 -100 150 100 50 0 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =3.8v, c in =1f c out =0.47f output voltage v out (v) output current output voltage 2.6 2.7 3.2 3.0 2.9 3.1 2.8 -150 -50 -100 150 100 50 0 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =3.8v, c in =1f c out =1f output voltage v out (v) output current output voltage r1163x281x eco=h r1163x281x eco=h 2.6 2.7 3.2 3.0 2.9 3.1 2.8 -120 -60 -90 60 30 0 -30 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =3.8v, c in =1f c out =0.47f output voltage v out (v) output current output voltage 2.6 2.7 3.2 3.0 2.9 3.1 2.8 -120 -60 -90 60 30 0 -30 04 21216 8 61418 10 20 time t(s) output current i out (ma) v in =3.8v, c in =1f c out =1f output voltage v out (v) output current output voltage
r1163x 24 r1163x281x eco=l r1163x281x eco=l 2.4 2.6 3.6 3.2 3.0 3.4 2.8 -40 -20 -30 20 10 0 -10 0.0 0.40.2 1.2 1.6 0.80.6 1.4 1.8 1.0 2.0 time t(ms) output current i out (ma) v in =3.8v, c in =1f c out =0.47f output voltage v out (v) output current output voltage 2.4 2.6 3.6 3.2 3.0 3.4 2.8 -40 -20 -30 20 10 0 -10 0.0 0.40.2 1.2 1.6 0.80.6 1.4 1.8 1.0 2.0 time t(ms) output current i out (ma) v in =3.8v, c in =1f c out =1f output voltage v out (v) output current output voltage 14) turn on speed with ce pin r1163x151x eco=h r1163x151x eco=l -5 -4 3 1 0 2 -2 -3 -1 -0.5 0.5 0.0 3.5 2.5 1.5 3.0 2.0 1.0 -8 0 16 24 832 -4 12 20 428 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =2.5v, c in =1f c out =0.47f i out =0ma output voltage ce input voltage -5 -4 3 1 0 2 -2 -3 -1 -0.5 0.5 0.0 3.5 2.5 1.5 3.0 2.0 1.0 -40 40 80 0 120 20 60 -20 100 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =2.5v, c in =1f c out =0.47f i out =0ma output voltage ce input voltage r1163x151x eco=h r1163x151x eco=l -5 -4 3 1 0 2 -2 -3 -1 -0.5 0.5 0.0 3.5 2.5 1.5 3.0 2.0 1.0 -8 0 16 24 832 -4 12 20 428 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =2.5v, c in =1f c out =0.47f i out =30ma output voltage ce input voltage -5 -4 3 1 0 2 -2 -3 -1 -0.5 0.5 0.0 3.5 2.5 1.5 3.0 2.0 1.0 -0.2 0 0.4 0.6 0.2 0.8 -0.1 0.3 0.5 0.1 0.7 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =2.5v, c in =1f c out =0.47f i out =30ma output voltage ce input voltage
r1163x 25 r1163x151x eco=h r1163x151x eco=l -5 -4 3 1 0 2 -2 -3 -1 -0.5 0.5 0.0 3.5 2.5 1.5 3.0 2.0 1.0 -8 0 16 24 832 -4 12 20 428 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =2.5v, c in =1f c out =0.47f i out =150ma output voltage ce input voltage -5 -4 3 1 0 2 -2 -3 -1 -0.5 0.5 0.0 3.5 2.5 1.5 3.0 2.0 1.0 -0.2 0 0.4 0.6 0.2 0.8 -0.1 0.3 0.5 0.1 0.7 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =2.5v, c in =1f c out =0.47f i out =150ma output voltage ce input voltage r1163x281x eco=h r1163x281x eco=l -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 7 5 3 6 4 2 -20 0 40 60 20 80 -10 30 50 10 70 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =3.8v, c in =1f c out =0.47f i out =0ma output voltage ce input voltage -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 7 5 3 6 4 2 -20 0 40 60 20 80 -10 30 50 10 70 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =3.8v, c in =1f c out =0.47f i out =0ma output voltage ce input voltage r1163x281x eco=h r1163x281x eco=l -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 7 5 3 6 4 2 -20 0 40 60 20 80 -10 30 50 10 70 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =3.8v, c in =1f c out =0.47f i out =30ma output voltage ce input voltage -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 7 5 3 6 4 2 -0.1 0 0.16 0.24 0.08 0.32 -0 0.12 0.2 0.04 0.28 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =3.8v, c in =1f c out =0.47f i out =30ma output voltage ce input voltage
r1163x 26 r1163x281x eco=h r1163x281x eco=l -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 7 5 3 6 4 2 -20 0 40 60 20 80 -10 30 50 10 70 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =3.8v, c in =1f c out =0.47f i out =150ma output voltage ce input voltage -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 7 5 3 6 4 2 -0.1 0 0.16 0.24 0.08 0.32 -0 0.12 0.2 0.04 0.28 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =3.8v, c in =1f c out =0.47f i out =150ma output voltage ce input voltage r1163x401x eco=h r1163x401x eco=l -12 -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 8 7 5 3 6 4 2 -20 0 40 60 20 80 -10 30 50 10 70 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =5.0v, c in =1f c out =0.47f i out =0ma output voltage ce input voltage -12 -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 8 7 5 3 6 4 2 -8 0 16 24 832 -4 12 20 428 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =5.0v, c in =1f c out =0.47f i out =0ma output voltage ce input voltage r1163x401x eco=h r1163x401x eco=l -12 -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 8 7 5 3 6 4 2 -20 0 40 60 20 80 -10 30 50 10 70 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =5.0v, c in =1f c out =0.47f i out =30ma output voltage ce input voltage -12 -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 8 7 5 3 6 4 2 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =5.0v, c in =1f c out =0.47f i out =30ma output voltage ce input voltage -0.1 0 0.16 0.24 0.08 0.32 -0 0.12 0.2 0.04 0.28
r1163x 27 r1163x401x eco=h r1163x401x eco=l -12 -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 8 7 5 3 6 4 2 -20 0 40 60 20 80 -10 30 50 10 70 time t(s) ce input voltage v ce (v) output voltage v out (v) v in =5.0v, c in =1f c out =0.47f i out =150ma output voltage ce input voltage -12 -10 -8 6 2 0 4 -4 -6 -2 -1 1 0 8 7 5 3 6 4 2 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =5.0v, c in =1f c out =0.47f i out =150ma output voltage ce input voltage -0.1 0 0.16 0.24 0.08 0.32 -0 0.12 0.2 0.04 0.28 15) turn off speed with ce pin r1163x151xd r1163x281xd -5 -4 -3 3 2 1 -1 -2 0 -0.5 0.0 3.5 3.0 2.0 1.0 2.5 1.5 0.5 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =2.5v, c in =1f c out =0.47f output voltage ce input voltage -0.1 0 0.16 0.24 0.08 0.32 -0 0.12 0.2 0.04 0.28 i out =0ma i out =30ma i out =150ma -5 -4 -3 4 3 2 1 -1 -2 0 -1.0 0.0 8.0 7.0 6.0 4.0 2.0 5.0 3.0 1.0 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =3.8v, c in =1f c out =0.47f output voltage ce input voltage -0.1 0 0.16 0.24 0.08 0.32 -0 0.12 0.2 0.04 0.28 i out =0ma i out =30ma i out =150ma r1163x401xd -6 -4 -3 6 5 2 4 3 -5 1 -1 -2 0 -1 0 11 9 7 10 8 6 4 2 5 3 1 time t(ms) ce input voltage v ce (v) output voltage v out (v) v in =5.0v, c in =1f c out =0.47f output voltage ce input voltage -0.1 0 0.16 0.24 0.08 0.32 -0 0.12 0.2 0.04 0.28 i out =0ma i out =30ma i out =150ma
r1163x 28 16) output voltage at mode alternative point r1163x151b/d r1163x281b/d 1.48 1.48 1.52 1.52 1.50 1.48 1.50 1.50 1.52 1.48 1.52 1.50 1.48 v in =2.5v, c in =ceramic 1.0 f, c out =ceramic 0.47 f time t(ms) -0.1 0.1 0.5 0.7 0.3 0.9 0.0 0.4 0.6 0.2 0.8 3 1.52 1.50 2 1 -1 0 eco input voltage v eco (v) i out =1ma i out =10ma i out =50ma i out =100ma i out =150ma output voltage v out (v) 2.78 2.82 2.80 2.80 2.78 2.82 2.78 2.78 2.80 2.82 2.80 2.82 v in =3.8v, c in =ceramic 1.0 f, c out =ceramic 0.47 f time t(ms) -0.1 0.1 0.5 0.7 0.3 0.9 0.0 0.4 0.6 0.2 0.8 4 2.80 2.82 2.78 3 2 1 0 -1 eco input voltage v eco (v) output voltage v out (v) i out =1ma i out =10ma i out =50ma i out =100ma i out =150ma 1.48 1.49 1.56 1.54 1.53 1.55 1.51 1.50 1.52 -5 -4 3 2 0 -2 1 -1 -3 -10 0 40 60 20 9080 30 50 10 70 time t(ms) output voltage v out (v) eco input voltage v eco (v) i out =0ma 2.78 2.79 2.86 2.84 2.83 2.85 2.81 2.80 2.82 -4 4 2 3 0 -2 1 -1 -3 -10 0 40 60 20 9080 30 50 10 70 time t(ms) output voltage v out (v) eco input voltage v eco (v) i out =0ma
r1163x 29 technical notes when using these ics, consider the following points: in these ics, phase compensation is made for securing st able operation even if the load current is varied. for this purpose, be sure to use a capacitor c out with good frequency characteristics and esr (equivalent series resistance) in the range described as follows: the relations between i out (output current) and esr of output ca pacitor are shown below. the conditions when the white noise level is under 40v (avg.) are marked as the hatched area in the graph. (1) frequency band: 10hz to 2mhz r1163x151x eco=h r1163x151x eco=l 0 40 80 120 20 60 100 140 load current i out (ma) topt=85c topt=25c topt=-40c 0.01 100 1 0.1 10 esr() v in =2.0v to 6.0v, c in =1f c out =0.47f 0 40 80 120 20 60 100 140 load current i out (ma) 0.01 100 1 0.1 10 esr() v in =2.0v to 6.0v, c in =1f c out =0.47f r1163x281x eco=h r1163x281x eco=l 0 40 80 120 20 60 100 140 load current i out (ma) topt=85c topt=25c topt=-40c 0.01 100 1 0.1 10 esr() v in =3.1v to 6.0v, c in =1f c out =0.47f 0 40 80 120 20 60 100 140 load current i out (ma) 0.01 100 1 0.1 10 esr() v in =3.1v to 6.0v, c in =1f c out =0.47f
http://www.e-devices.ricoh.co.jp/en/ 4bmft4vqqpsu0$?dft 3*$0)&-&$530/*$%&7*$&4$0 -5% )jhbtij4ijobhbxb0$?df *oufsobujpobm4bmft
)jhbtij4ijobhbxb 4ijobhbxblv 5plzp +bqbo 1ipof'by 3*$0)&6301& /&5)&3-"/%4
#7 4fnjdpoevdups4vqqpsu$fousf 1spg8),fftpnmbbo %+"ntufmwffo 5if/fuifsmboet 1ipof 3*$0)&-&$530/*$%&7*$&4,03&"$0 -5% ' )bftvoh#meh 5fifsbosp (bohobnhv 4fpvm ,psfb 1ipof'by 3*$0)&-&$530/*$%&7*$&44)"/()"*$0 -5% 3ppn /p#vjmejoh /p#jcp3pbe 1v%poh/fx%jtusjdu 4ibohibj 1fpqmft3fqvcmjdpg$ijob 1ipof'by 3*$0)&-&$530/*$%&7*$&4$0 -5% 5bjqfjp$?df 3ppn ' /p )fohzboh3e 5bjqfj$juz 5bjxbo 30$
1ipof'by ricoh is committed to reducing the environmental loading materials in electrical devices with a view to contributing to the protection of human health and the environment. ricoh has been providing rohs compliant products since april 1, 2006 and halogen-free products since april 1, 2012. halogen free 5ifqspevdutboeuifqspevdutqfdjpdbujpoteftdsjcfejouijtepdvnfoubsftvckfduupdibohfps ejtdpoujovbujpopgqspevdujpoxjuipvuopujdfgpssfbtpot tvdibtjnqspwfnfou5ifsfgpsf cfgpsf efdjejohupvtfuifqspevdut qmfbtfsfgfsup3jdpitbmftsfqsftfoubujwftgpsuifmbuftujogpsnbujpo uifsfpo 5ifnbufsjbmtjouijtepdvnfounbzopucfdpqjfepspuifsxjtfsfqspevdfejoxipmfpsjoqbsuxjuipvu qsjpsxsjuufodpotfoupg3jdpi 1mfbtfcftvsfupublfbozofdfttbszgpsnbmjujftvoefssfmfwboumbxtpssfhvmbujpotcfgpsffyqpsujohps puifsxjtfubljohpvupgzpvsdpvouszuifqspevdutpsuifufdiojdbmjogpsnbujpoeftdsjcfeifsfjo 5ifufdiojdbmjogpsnbujpoeftdsjcfejouijtepdvnfoutipxtuzqjdbmdibsbdufsjtujdtpgboefybnqmf bqqmjdbujpodjsdvjutgpsuifqspevdut5ifsfmfbtfpgtvdijogpsnbujpojtopuupcfdpotusvfebtb xbssbouzpgpsbhsboupgmjdfotfvoefs3jdpitpsbozuijseqbsuztjoufmmfduvbmqspqfsuzsjhiutpsboz puifssjhiut 5ifqspevdutmjtufejouijtepdvnfoubsfjoufoefeboeeftjhofegpsvtfbthfofsbmfmfduspojd dpnqpofoutjotuboebsebqqmjdbujpot p$?dffrvjqnfou ufmfdpnnvojdbujpofrvjqnfou nfbtvsjoh jotusvnfout dpotvnfsfmfduspojdqspevdut bnvtfnfoufrvjqnfoufud
5iptfdvtupnfstjoufoejohup vtf bqspevdujobobqqmjdbujposfrvjsjohfyusfnfrvbmjuzboesfmjbcjmjuz gpsfybnqmf jobijhimztqfdjpd bqqmjdbujpoxifsfuifgbjmvsfpsnjtpqfsbujpopguifqspevdudpvmesftvmujoivnbojokvszpsefbui bjsdsbgu tqbdfwfijdmf ovdmfbssfbdupsdpouspmtztufn usb$?ddpouspmtztufn bvupnpujwfboe usbotqpsubujpofrvjqnfou dpncvtujpofrvjqnfou tbgfuzefwjdft mjgftvqqpsutztufnfud
tipvmepstu dpoubduvt 8fbsfnbljohpvsdpoujovpvtf$?psuupjnqspwfuifrvbmjuzboesfmjbcjmjuzpgpvsqspevdut cvu tfnjdpoevdupsqspevdutbsfmjlfmzupgbjmxjuidfsubjoqspcbcjmjuz*opsefsupqsfwfoubozjokvszup qfstpotpsebnbhftupqspqfsuzsftvmujohgspntvdigbjmvsf dvtupnfsttipvmecfdbsfgvmfopvhiup jodpsqpsbuftbgfuznfbtvsftjouifjseftjho tvdibtsfevoebodzgfbuvsf psfdpoubjonfougfbuvsfboe gbjmtbgfgfbuvsf8fepopubttvnfbozmjbcjmjuz pssftqpotjcjmjuzgpsbozmpttpsebnbhfbsjtjohgspn njtvtfpsjobqqspqsjbufvtfpguifqspevdut "oujsbejbujpoeftjhojtopujnqmfnfoufejouifqspevduteftdsjcfejouijtepdvnfou 1mfbtfdpoubdu3jdpitbmftsfqsftfoubujwfttipvmezpvibwfbozrvftujpotpsdpnnfoutdpodfsojoh uifqspevdutpsuifufdiojdbmjogpsnbujpo

▲Up To Search▲

Price & Availability of R1163N301D-TR-FE

	To Download R1163N301D-TR-FE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .